双曲线钢管调直机（出口型）
用处 Applications
本机实用于修建用的钢管创新、除锈、喷漆实验一次性机器化完成，到达每条钢管一致干净，油漆匀称的结果，本机事情服从高，能每分钟完成两条6米的速率，开脱了已往用人工除锈，喷油的庞大步伐，是各巨细修建商钢管除锈的抱负设置装备摆设。
This machine is suitable for construction of pipe renovation, rust, paint mechanized complete one-off, to achieve unity of each pipe clean, paint a uniform effect, high working efficiency of the machine, to complete the two speed of 6 meters per minute, to get rid of the conventional artificial rust, complicated procedure of fuel injection, the size of the device is ideal for builders steel rust.
参数Technical parameters
型号 | 电压 | 功率 | 利用范畴 | 调直服从 | 调直速率 | 实际分量 | 形状尺寸 |
| Rated voltage | Power | Diameter Range | Estraigh enfficiency | Work Efficiency | weight | Overall dimensions |
AY48-4 | 380V | 10KW+0.2KW | Φ46-49 | ≤3° | 18米/分钟 | 1100KG | ### |
留意事变 Application notice
1、本机实用于380V、频率50Hz、三相电源。利用前请左右反省所利用的电源能否切合本秘密求。本机应制止雨淋及溅水，为左右的宁静起见，本机必需牢靠接地或安置泄电开关。
This applies to 380V, frequency 50Hz, three-phase power. Before use, check your power supply used by the machine meets the requirements. The machine should avoid rain and splashing water for your safety, the machine must be grounded or install GFCI.
2、本机应安顿在程度的空中，确保呆板的安稳，进、出管口辨别要与别的修建物坚持6米以上间隔
The machine should be placed at ground level, to ensure a smooth machine, into and out of the nozzle, respectively, to maintain more than 6 meters away from buildings and other
3、新机利用时该当反省变速箱、链条等传动部件的机油能否正常，若有停转或呈现非常响声时应堵截电源停机反省，扫除妨碍前方可利用。
Should check the gearbox, drive chains and other parts of a new machine oil is normal, if stalling or abnormal sound should cut off the power down to check, troubleshooting before use.
4、喷油时把已调好的油漆注意灌输油桶内以确保流量，到达最佳功能。
用处 Applications
本机实用于修建用的钢管创新、除锈、喷漆实验一次性机器化完成，到达每条钢管一致干净，油漆匀称的结果，本机事情服从高，能每分钟完成两条6米的速率，开脱了已往用人工除锈，喷油的庞大步伐，是各巨细修建商钢管除锈的抱负设置装备摆设。
This machine is suitable for construction of pipe renovation, rust, paint mechanized complete one-off, to achieve unity of each pipe clean, paint a uniform effect, high working efficiency of the machine, to complete the two speed of 6 meters per minute, to get rid of the conventional artificial rust, complicated procedure of fuel injection, the size of the device is ideal for builders steel rust.
参数Technical parameters
型号 | 电压 | 功率 | 利用范畴 | 调直服从 | 调直速率 | 实际分量 | 形状尺寸 |
| Rated voltage | Power | Diameter Range | Estraigh enfficiency | Work Efficiency | weight | Overall dimensions |
AY48-4 | 380V | 10KW+0.2KW | Φ46-49 | ≤3° | 18米/分钟 | 1100KG | ### |
留意事变 Application notice
1、本机实用于380V、频率50Hz、三相电源。利用前请左右反省所利用的电源能否切合本秘密求。本机应制止雨淋及溅水，为左右的宁静起见，本机必需牢靠接地或安置泄电开关。
This applies to 380V, frequency 50Hz, three-phase power. Before use, check your power supply used by the machine meets the requirements. The machine should avoid rain and splashing water for your safety, the machine must be grounded or install GFCI.
2、本机应安顿在程度的空中，确保呆板的安稳，进、出管口辨别要与别的修建物坚持6米以上间隔
The machine should be placed at ground level, to ensure a smooth machine, into and out of the nozzle, respectively, to maintain more than 6 meters away from buildings and other
3、新机利用时该当反省变速箱、链条等传动部件的机油能否正常，若有停转或呈现非常响声时应堵截电源停机反省，扫除妨碍前方可利用。
Should check the gearbox, drive chains and other parts of a new machine oil is normal, if stalling or abnormal sound should cut off the power down to check, troubleshooting before use.
4、喷油时把已调好的油漆注意灌输油桶内以确保流量，到达最佳功能。
When the injection has been tuned paint poured into the barrel to make sure that the flow to achieve the best performance.
5、每次利用完后，必需要活期调养全机链条加光滑油（黄油），一样平常在7-15天左右加油一次。
after each use, regular maintenance of the whole machine must lubricate the chain （butter）， typically 7-15 days refuel again.
6、本机只实用于48mm的钢管，但凡有严峻变型，有焊口或启齿的钢管都不克不及在本机上操纵。
the machine is only available in 48mm pipe, where there are serious variations, there is an opening or pipe weld can not operate on this unit.
7、操纵职员不克不及够佩戴手套，坚持与本机入口一米以上间隔，避免近间隔打仗入口旋转伦，制止伤手。
The operator can not wear gloves to keep up with the machine more than one meter from the entrance to prevent close contact with inlet swivel Lun, avoid hand injuries.
